U.S. Non-Federal-Government Allocations
FIXED
MARITIME MOBILE
Radiolocation
FCC rule parts
SpectrumWiki
Radio spectrum allocations
Look up a frequency or a range.
Examples: 88.5 MHz, 1350–1430 MHz, 2.4 GHz
128.999 kHz (128,999 Hz)
U.S. Federal Government Allocations
FIXED
MARITIME MOBILE
Radiolocation
ITU Region 1 Allocations
RADIONAVIGATION 5.60
ITU Region 2 Allocations
FIXED
MARITIME MOBILE
MARITIME RADIONAVIGATION 5.60
Radiolocation
ITU Region 3 Allocations
RADIONAVIGATION 5.60
Fixed
Maritime mobile
Footnotes
-
5.60 In the bands 70-90 kHz (70-86 kHz in Region 1) and 110-130 kHz (112-130 kHz in Region 1), pulsed radionavigation systems may be used on condition that they do not cause harmful interference to other services to which these bands are allocated.
-
5.61 In Region 2, the establishment and operation of stations in the maritime radionavigation service in the bands 70-90 kHz and 110-130 kHz shall be subject to agreement obtained under No. 9.21 with administrations whose services, operating in accordance with the Table, may be affected. However, stations of the fixed, maritime mobile and radiolocation services shall not cause harmful interference to stations in the maritime radionavigation service established under such agreements.
-
5.64 Only classes A1A or F1B, A2C, A3C, F1C or F3C emissions are authorized for stations of the fixed service in the bands allocated to this service between 90 kHz and 160 kHz (148.5 kHz in Region 1) and for stations of the maritime mobile service in the bands allocated to this service between 110 kHz and 160 kHz (148.5 kHz in Region 1). Exceptionally, class J2B or J7B emissions are also authorized in the bands between 110 kHz and 160 kHz (148.5 kHz in Region 1) for stations of the maritime mobile service.
-
5.65 Different category of service: in Bangladesh, the allocation of the bands 112-117.6 kHz and 126-129 kHz to the fixed and maritime mobile services is on a primary basis (see No. 5.33). (WRC 2000)
-
US2 In the band 9-490 kHz, electric utilities operate Power Line Carrier (PLC) systems on power transmission lines for communications important to the reliability and security of electric service to the public. These PLC systems operate under the provisions of 47 CFR part 15, or Chapter 8 of the NTIA Manual, on an unprotected and non-interference basis with respect to authorized radio users. Notification of intent to place new or revised radio frequency assignments or PLC frequency uses in the band 9-490 kHz is to be made in accordance with the Rules and Regulations of the FCC and NTIA, and users are urged to minimize potential interference to the extent practicable. This footnote does not provide any allocation status to PLC radio frequency uses.
Wiki entries
Radiofrequency Identification (RFID)
Current Use
9–135 kHz RFID (inductive systems)
An RFID system consists of an interrogator and a transponder, and is used for identification and data capture. RFID systems are used for a very wide range of applications, including:
Highway tolls
Vehicle tracking
Container tracking
Inventory control & theft prevention (often used to prevent shoplifting)
Healthcare (patient & drug tracking)
Passports
ID cards
Building entry
Livestock & pet tracking
and numerous other applications.
RFID tags can be extremely small devices with little or no internal power, which respond to an interrogation by utilizing some of the RF energy imparted by the interrogator; or they can be larger powered units that can be interrogated over larger distances.
The ITU is in the process of attempting to harmonize RFID bands, since RFID systems are used for global commerce. ITU Study Group 1 (Working Party 1B) is drafting a new ITU-R Recommendation on RFID.
ISO/IEC18000 is the principal standard for the RFID air interface.
RFID systems typically operate in ISM and unlicensed bands.
The bands listed below represent the totality of the various bands presently used around the world. The exact bands used in specific countries may vary (and is what the ITU is attempting to harmonize).
Highway tolls
Vehicle tracking
Container tracking
Inventory control & theft prevention (often used to prevent shoplifting)
Healthcare (patient & drug tracking)
Passports
ID cards
Building entry
Livestock & pet tracking
and numerous other applications.
RFID tags can be extremely small devices with little or no internal power, which respond to an interrogation by utilizing some of the RF energy imparted by the interrogator; or they can be larger powered units that can be interrogated over larger distances.
The ITU is in the process of attempting to harmonize RFID bands, since RFID systems are used for global commerce. ITU Study Group 1 (Working Party 1B) is drafting a new ITU-R Recommendation on RFID.
ISO/IEC18000 is the principal standard for the RFID air interface.
RFID systems typically operate in ISM and unlicensed bands.
The bands listed below represent the totality of the various bands presently used around the world. The exact bands used in specific countries may vary (and is what the ITU is attempting to harmonize).